OEM 803697896 The XCMG Rubber-Coated Clamp 803697896 is a genuine OEM clamp with a bonded rubber cushion that holds hydraulic lines without scuffing them on XCMG excavators.
Marked with part number 803697896, this factory clamp pairs a steel band with a molded rubber liner, so the line stays gripped but its outer cover is protected.
The steel body is stamped and edge rolled, then plated against corrosion, while the rubber cushion resists oil, heat and ageing.
Exact inner diameter, band width and bolt hole spacing let the clamp bolt to the original mounting point without bending or shimming.
The rubber layer absorbs vibration and stops metal-to-hose contact, which is where abrasion damage and pinhole leaks usually begin.
Every clamp is gauged and trial fitted before packing, so the part that reaches your bench matches the XCMG drawing without rework.
The 803697896 clamp combines a spring-grade steel band with a molded rubber liner, so it grips firmly without marking the hose cover.
Its diameter and hole spacing follow the OEM pattern, so the clamp bolts to the frame without opening, closing or slotting.
The bonded cushion stays attached under vibration, so the rubber does not peel away and leave metal rubbing on rubber.
A plated or coated steel finish fights rust through wet seasons, washdowns and salt spread on winter haul roads.
Cushioning spreads clamping load over a wider area, so the tube stays round and flow remains smooth instead of pinched.
The rubber layer also damps vibration, which lowers noise and reduces fatigue at nearby fittings and brackets.
Because the part fits straight out of the bag, a technician finishes the job in minutes rather than cutting a homemade cushion.
Production opens with certified steel strip checked for thickness, temper, width and surface condition before stamping.
Press tools shape the band to the drawing diameter, and edge rolling removes burrs that could cut the rubber cushion.
The rubber liner is molded and bonded under controlled heat and pressure, so it stays fixed to the band in service.
Inspectors verify diameter, width, cushion thickness and hole position against a checking gauge made for this part number.
Batch records trace every 803697896 clamp to its steel coil and rubber lot, so any question is traced and settled fast.
The clamp holds a hose or pipe against the frame, so the line stays on its designed route through every work cycle.
A bare metal clamp wears the hose cover away, and once the reinforcement is exposed the line can burst under pressure.
The genuine 803697896 keeps rubber against rubber, so the line is held firmly but its outer skin is never scuffed.
The cushion also absorbs shock from bucket impacts and rough ground, which lowers peak load on the clamps and fittings.
Sound line retention protects pumps, valves and cylinders, which keeps cycle times and machine availability predictable.
The 803697896 clamp installs with a socket set and torque wrench during scheduled hydraulic or structural service.
Relieve hydraulic pressure, stop the engine and support the line before removing any clamp along the route.
Unbolt the old clamp, clean the mounting face and check the frame threads for rust, damage or cross-threading.
Seat the new clamp over the hose with the rubber facing the line, start the bolt by hand, then torque it correctly.
Confirm the clamp base sits flush on the frame and that no gap or tilt exists under the band.
Start the engine, cycle the functions slowly, and watch the clamp and nearby line for shifting or rubbing.
At service intervals, check the rubber for cuts or separation and replace the clamp before the cushion wears through.
Every 803697896 clamp is produced in an ISO 9001 and ISO 14001 certified plant with traceability from steel to sealed carton.
Incoming strip is tested for thickness and temper, and finished clamps are gauged for diameter, width and cushion thickness.
During production, press force, bonding temperature and coating thickness are monitored so each unit matches the reference sample.
Final checks include visual inspection, dimensional verification and a trial fit on the XCMG line fixture for this machine series.
Samples from each batch undergo holding load, rubber peel, salt spray and vibration tests to confirm long-term performance.
Cheap copies often use a loose rubber sleeve instead of a bonded cushion, so the liner slips and the metal rubs the hose.
A clamp with the wrong diameter pinches the line or leaves it loose, and both cases end in chafing or leaking.
The genuine 803697896 is formed to the XCMG drawing, so diameter, band width, cushion and hole spacing mirror the original.
Staying with genuine XCMG parts keeps warranty cover intact, protects resale value and avoids clashes with other OEM items.
Every clamp carries XCMG global quality standards and technical backing, so it works through long shifts in harsh ground.
Fitting the genuine 803697896 clamp stops a small rub from growing into a costly hydraulic hose replacement.
When a bare clamp wears through a cover, the line can burst and dump oil fast, which can take out a pump in minutes.
Sound steel and a well-bonded cushion keep the clamp working across a long service life, reducing replacement frequency.
Cushioned retention also lengthens hose, seal and oil life, which trims the total cost of ownership for fleet owners.
Maintenance logs from quarry and construction fleets show genuine XCMG parts reduce unplanned stoppages.
XCMG builds the 803697896 clamp with efficient nesting and controlled stamping that keep material scrap low.
A long working life means fewer replacements, which lowers the raw material and energy tied to each clamp.
Containing hydraulic leaks protects soil and groundwater, helping operators meet rules on sensitive job sites.
The steel, rubber and plating in this part comply with RoHS and REACH requirements for safe handling and responsible recycling.
The 803697896 rubber-coated clamp is stocked in XCMG depots serving North America, Europe, Asia and Australia.
Each clamp is bagged and boxed in strong cartons that guard against bending, dust and damp during transport.
Fleet buyers can request volume pricing and combined freight, which simplifies planning and lowers landed cost.
Live stock data and responsive supply teams help cover urgent requests fast, so machines return to work sooner.
Careful packing keeps the clamp in factory condition until fitting, avoiding the cushion damage seen in badly stored stock.
The XCMG Rubber-Coated Clamp 803697896 is a key retention part on XCMG excavators, holding hydraulic lines without scuffing them.
Its spring-grade steel band, bonded rubber cushion and durable coating deliver dependable grip in hot, wet and dusty conditions.
By blocking chafing and vibration, this rubber-coated clamp cuts downtime, lowers repair bills and adds service life to the line.
Buy only genuine XCMG parts from authorised dealers to secure real quality, correct fitment and lasting performance.
Specify the 803697896 rubber-coated clamp for a dependable hold and confident, trouble-free servicing.
Work with XCMG, a trusted supplier of engine and hydraulic components for heavy equipment that delivers real value.
OEM 803697896 – XCMG Rubber-Coated Clamp – the definitive cushioned clamp for hose and pipe retention on your excavator. Built for strength, lined for protection, and supported by global quality standards. Trust the original to protect your investment and keep uptime high.
