OEM 800158271 The XCMG T-Clamp 800158271 is a genuine OEM T-bolt clamp engineered to secure high-pressure charge-air and coolant hoses on XCMG hydraulic excavators.
Identified by part number 800158271, this factory-made clamp applies uniform clamping force around the hose, so the connection stays tight under pressure and vibration.
It is formed from high-strength stainless or zinc-plated steel strip with a forged T-bolt and a captive nut that resists loosening.
Exact OEM diameter, band width, and bolt size allow direct replacement without shimming, bending, or adding extra sealing material.
By holding even clamp load around the full circumference, this T-clamp prevents hose blow-off, weep leaks, and pressure loss in the circuit.
The 800158271 T-Clamp is formed from high-strength steel strip that resists stretching, so clamping force stays steady under pressure spikes.
The T-bolt and captive nut apply load evenly around the full band, which prevents the concentrated pinching common with worm-drive clamps.
A rolled band edge protects the hose cover from cutting, so the hose stays intact even when the clamp is tightened to full torque.
Stainless or zinc-plated finish resists rust and galvanic corrosion, keeping the clamp removable after years of outdoor service.
The captive nut stays attached to the band, so installation is fast and small parts cannot be lost in the engine bay.
Exact OEM diameter and width allow direct replacement, keeping repairs within standard procedure and avoiding improvised hardware.
Production begins with certified steel strip checked for thickness, width, and tensile strength before stamping begins.
Progressive dies form the band and roll the edges, so the clamp seats flat on the hose without sharp edges that could cut rubber.
The T-bolt thread is rolled to the specified pitch, and the captive nut is staked so it stays on the band but still turns freely.
Inspectors check clamping diameter, band width, thread fit, and coating thickness on samples from every production lot.
Batch records let XCMG trace each 800158271 clamp back to its steel coil and forming run, so quality questions are resolved quickly.
Excavators run charge-air and coolant hoses under pressure, and those hoses vibrate constantly during digging and travel.
A worm-drive clamp can loosen or cut into the hose, which leads to boost leaks, coolant loss, and unexpected downtime.
The genuine 800158271 spreads load evenly around the hose, so the connection holds pressure and the hose cover stays undamaged.
Even clamping also reduces vibration at the joint, which protects nearby pipes, brackets, and sensor fittings.
Correct clamping force keeps the system sealed, so engine performance and cooling efficiency remain stable all shift.
The 800158271 T-Clamp installs with a standard socket and torque wrench, adding only minutes to a hose repair.
Park the excavator on firm level ground, lower the attachment, release pressure, and lock out the machine before starting work.
Slide the clamp over the hose end, push the hose fully onto the fitting, and position the clamp behind the bead.
Tighten the T-bolt to the torque value in the XCMG workshop manual, checking that the band stays square on the hose.
Run the engine at low idle, check for leaks or boost loss, and confirm the clamp has not shifted under pressure.
During routine maintenance, check clamps for rust, stripped threads, and looseness, and replace any damaged clamp promptly.
Every 800158271 clamp is produced in an ISO 9001 and ISO 14001 certified plant with traceability from steel coil to packed carton.
Incoming steel is tested for thickness and strength, and finished clamps are checked for diameter, band width, and thread fit.
During production, die wear and sample dimensions are monitored so drift is corrected before parts leave the line.
Post-production checks include visual inspection, coating thickness measurement, and a torque trial on the XCMG hose fitting fixture.
Sample clamps from each batch undergo salt spray and vibration tests to confirm corrosion resistance and clamp stability in the field.
Low-cost aftermarket T-clamps often use thin band steel or soft bolts that stretch, strip, or break under full torque.
A clamp with the wrong diameter can sit loose or cut into the hose, causing leaks and hose failure within a short time.
The genuine 800158271 is built to the XCMG drawing, so diameter, band width, bolt thread, and finish match the original part.
Using genuine XCMG parts also preserves warranty coverage, protects resale value, and maintains compatibility with other OEM components.
Backed by XCMG global quality standards and technical support, this T-clamp delivers dependable clamping in harsh conditions.
Choosing the genuine 800158271 clamp prevents a small hose leak from turning into a costly boost or coolant system repair.
A failed clamp can let a hose blow off under pressure, which stops the machine and may damage the hose, fitting, or nearby parts.
Durable steel and proper coating keep clamping force consistent across a long service life, reducing replacement frequency.
Reliable clamping also extends hose and fitting life, lowering the total cost of ownership for fleet operators.
Fleet records from construction and mining operations show genuine XCMG clamps help cut hose-related downtime.
XCMG applies sustainable manufacturing to the 800158271 clamp through recyclable steel content and efficient stamping processes.
The long service life of the clamp reduces material consumption and lowers the environmental footprint of replacement parts.
Preventing boost and coolant leaks supports cleaner operation and reduces fluid loss on sensitive construction sites.
Steel and coating materials in this component comply with RoHS and REACH rules for safe handling and responsible disposal.
The 800158271 T-Clamp is held in XCMG regional distribution centres across North America, Europe, Asia, and Australia.
Each unit is bagged and packed in a sturdy carton that protects the band and threads from moisture, dust, and impact in transit.
For fleet-wide orders, XCMG provides volume pricing and consolidated freight options that simplify planning and reduce cost.
Real-time stock visibility and dedicated supply chain support help fill urgent requests quickly, shortening downtime on active projects.
Robust packaging preserves factory condition until installation, preventing the thread damage and band distortion common in stored spares.
The XCMG T-Clamp 800158271 is a vital hose-securing component for XCMG excavators, holding connections tight under pressure and vibration.
Its high-strength band, forged T-bolt, and corrosion-resistant finish deliver dependable clamping in hot, wet, and dusty environments.
By preventing hose blow-off and leaks, this T-clamp reduces downtime, lowers maintenance costs, and extends hose and fitting life.
Always purchase genuine XCMG parts from authorised dealers to guarantee authenticity, quality, and performance for your equipment fleet.
Choose the 800158271 T-Clamp for dependable hose connections and lasting operational peace of mind.
Partner with XCMG, your trusted source for heavy equipment engine and hydraulic components that deliver real value.
OEM 800158271 – XCMG T-Clamp – the definitive T-bolt hose clamp solution for your excavator charge-air and coolant connections. Engineered for even clamping force, designed for exact fitment, and backed by global quality standards. Trust the original to protect your investment and maximise uptime.
