OEM 801973667 The XCMG Pin 801973667 is a genuine small retaining pin measuring 2.5 mm by 12 mm that locks clips, levers and covers on XCMG hydraulic excavators.
Issued under the official part number 801973667, the pin gives the technician a correctly sized part that matches the hole, groove and grip length it is designed for.
The 2.5 mm diameter and 12 mm length are turned to the XCMG drawing, so the pin passes through the bore without force or reaming.
A smooth shank and chamfered ends let the pin start cleanly, so it does not cut the bore or push out a bushing during fitting.
A protective plating resists water, dust and corrosion, so the pin keeps its diameter and does not rust into place over time.
Every piece is checked for diameter, length, chamfer, straightness and finish before the batch is packed for shipment.
Fitted to linkage clips, handle pivots, cover hinges and trim panels, this pin keeps small joints locked and aligned.
The 801973667 pin is produced to the XCMG drawing, so the 2.5 mm diameter and 12 mm length fit the hole on the first attempt.
A straight shank and chamfered ends let the pin start cleanly, so it does not cut the bore or push out a small bushing.
Correct fit holds clips and levers in place, so the retained part does not rattle loose or fall off during work.
The plated finish resists water, dust and wash chemicals, so the pin does not rust into the bore and seize over time.
Because the part matches the OEM number, a fitter installs it straight from the bag without reaming or adding a sleeve.
Correct hardness keeps the pin straight under shear load, so it does not bend or shear off inside a small joint.
A sound pin also keeps cover hinges and trim panels attached, which protects the parts behind them from dust and loss.
Keeping spare pins on the shelf shortens repair time, so a lost retainer does not turn into a full day of lost work.
Each lot begins with certified steel wire or bar tested for chemistry, hardness and tensile strength before turning.
Pins are turned on CNC equipment, so the diameter, length and chamfer stay uniform from batch to batch.
Deburring removes sharp edges from the ends and any groove, so the pin slides in cleanly and does not cut the bore.
Inspectors measure diameter, length, chamfer and straightness against a gauge made for this exact part number.
Batch records trace every 801973667 pin to its steel lot and production run, so a quality question is settled quickly.
A small pin locks clips, levers and covers in place, so the retained part stays where it was designed to sit.
A missing or bent pin lets the retained part work loose, which can jam a lever or let a cover drop off the machine.
The genuine 801973667 keeps the small joint locked, so the part stays attached and the machine stays tidy and safe.
Correct fit avoids both a pin that falls out of an oversize hole and one that cracks the boss when pressed in too hard.
A sound pin protects covers, hinges and trim, which keeps service access easy and extends the life of the panel.
The 801973667 pin is installed with a cleaning cloth, a punch and pliers during cab, cover or trim service work.
Remove the old pin, clean the hole and check the bore so no dirt or metal chips sit under the new part.
Check the hole and boss for burrs, rust or cracks, since a rough surface will stop the pin seating straight.
Align the parts, start the pin by hand and press it in with a punch until the end sits flush with the boss.
Fit the retaining ring or clip where the drawing calls for one, so the pin cannot walk out under vibration.
Move the retained part slowly, then check that the pin stays put and the cover or lever moves freely.
At service intervals, look for a loose pin, a missing clip or a bent shank and renew the part before it drops out.
Every 801973667 pin is produced in an ISO 9001 and ISO 14001 certified plant with traceability from steel to carton.
Incoming steel is tested for hardness and chemistry, and finished pins are gauged for diameter, length and chamfer.
Each batch is screened for cracks, bends and coating defects, since these flaws let the pin shear or fall out under load.
Post-production checks include visual review, dimensional verification and a trial fit in the XCMG hole fixture.
Sample pins from each batch undergo shear, vibration and salt spray tests to confirm strength and corrosion performance.
Cheap copies often use soft wire or rough turning, so the pin bends, shears or falls out soon after installation.
A pin with the wrong diameter or length can sit proud, crack a small boss or fail to hold the clip in place.
The genuine 801973667 is made to the XCMG drawing, so diameter, length, chamfer and material match the original part.
Using genuine XCMG parts also preserves warranty coverage, protects resale value and keeps fit with OEM fittings.
Backed by XCMG global quality standards and technical support, this pin performs reliably in harsh conditions.
Choosing the genuine 801973667 pin prevents a small loss from turning into a dropped cover or a jammed lever.
A failed pin lets the retained part drop off, which can damage trim, wiring or whatever sits beneath it.
A correctly made pin holds firmly, so it does not need repeated replacement and does not wear out the hole.
Reliable pins also keep panels attached, which improves the appearance and lowers overall ownership cost.
Service records from construction and mining fleets show genuine XCMG parts cut unplanned downtime.
XCMG produces the 801973667 pin with efficient turning runs that keep production scrap low.
A long service life means fewer replacements, which lowers the material and energy tied to each pin.
Keeping covers and trim attached prevents damage and waste, which keeps the machine presentable and usable.
The materials in this part comply with RoHS and REACH requirements for safe handling and responsible recycling.
The 801973667 pin is stocked in XCMG depots serving North America, Europe, Asia and Australia.
Each unit is bagged to protect the finish and boxed in a strong carton that guards against dust, damp and crushing.
Fleet buyers can request volume pricing and combined freight, which simplifies planning and lowers landed cost.
Live stock data and responsive supply teams cover urgent requests fast, so machines return to work sooner.
Careful packing keeps the pin straight and the chamfer undamaged until fitting, avoiding the damage seen in loose storage.
The XCMG Pin 801973667 is a small but important retaining part on XCMG excavators, locking clips, levers and covers.
Its exact 2.5×12 size, clean chamfer and durable material deliver dependable retention in rain, dust and heat.
By keeping small joints locked, this pin cuts downtime, protects panels and extends the life of the assembly.
Buy only genuine XCMG parts from authorised dealers to secure real quality, correct fitment and lasting performance.
Specify the 801973667 pin for dependable retention and confident, trouble-free servicing.
Work with XCMG, a trusted supplier of engine and hydraulic components for heavy equipment that delivers real value.
OEM 801973667 – XCMG Pin 2.5×12 – the definitive small retainer for locked clips, levers and covers on your excavator. Turned to the drawing, finished for a precise fit, and backed by global quality standards. Trust the original to protect your investment and maximise uptime.
