OEM 801970620 The XCMG Water Pipe φ10×1100 801970620 is a genuine OEM water pipe with a 10 mm bore and 1100 mm length, delivering coolant between the engine and cooling system of XCMG excavators.
Stamped with part number 801970620, this factory pipe gives mechanics a rigid, sealed line that replaces the original without cutting, welding or adding adapters.
The pipe is formed from coolant-resistant steel tube, bent to the OEM path, then protected with an anti-corrosion coating inside and out.
Exact 10 mm diameter, wall thickness, 1100 mm length and bend radius let the pipe drop in without trimming or fitting extra parts.
A sealed water path keeps coolant inside the system, so the water pump moves liquid instead of air and the engine stays at working temperature.
Every pipe is pressure checked, flushed and measured before packing, so the part that arrives at your workshop matches the XCMG drawing exactly.
The 801970620 water pipe is formed from coolant-resistant material that keeps its strength and shape through hot and cold cycles.
Its exact 10 mm bore keeps coolant velocity in the designed range, so the pump does not have to work against an oversize passage.
The 1100 mm length follows the OEM route, so the pipe reaches both connections without kinking or stretching at the hoses.
A bonded anti-corrosion coating shields the outer surface from mud, moisture and salt spray found on excavation sites.
Ends are shaped to the original pattern, so hoses and clamps seat correctly on the first attempt without rework.
Rigid construction resists vibration fatigue better than a soft hose on hot, high-cycle coolant runs.
A smooth inner wall limits pressure loss, which helps the water pump deliver consistent flow at all engine speeds.
Production opens with certified tube or composite checked for wall thickness, roundness, hardness and surface defects.
A mandrel bender holds the drawing angles and radii within tight limits, so each pipe matches the master sample.
After bending, ends are formed, deburred and flushed so no chips or scale can enter the cooling circuit.
Inspectors check bend angle, center distance, the 1100 mm length and end geometry against a checking fixture for this part number.
Batch records trace every 801970620 pipe back to its material lot and bending program, so quality questions close fast.
The water pipe carries coolant between the engine, radiator and water pump along a fixed, protected route.
A cracked or corroded pipe leaks coolant and lets air enter, which causes overheating and poor heater performance.
The genuine 801970620 keeps the circuit sealed, so coolant stays inside and the pump moves liquid at full efficiency.
Correct routing away from exhaust heat and moving parts prevents damage, which extends the service life of the pipe.
Stable coolant flow protects the radiator, pump and cylinder head, which keeps engine output and uptime predictable.
The 801970620 water pipe installs with standard hand tools and hose clamp pliers during cooling system service.
Let the engine cool fully, then place a drain pan under the pipe before loosening any clamp or fastener.
Drain the coolant to a safe level, release the clamps and remove the old pipe from both connections.
Clean the mating surfaces and check for corrosion, cracks or flattened beads that could leak under pressure.
Set the new pipe in position, fit the hoses and clamps, then tighten the mounting fasteners to the specified torque.
Refill with the correct coolant mix, run the engine to temperature, and bleed trapped air from the system.
Check both connections for weeping after the first heat cycle, then top up once the engine has cooled.
At service intervals, look for rust spots, dents or chafing marks, and replace the pipe before a leak grows.
Every 801970620 pipe is produced in an ISO 9001 and ISO 14001 certified plant with traceability from material to packed carton.
Incoming tube is tested for wall thickness and grade, and finished pipes are measured for bore, length and bend angle.
During production, bending force, mandrel condition and coating thickness are monitored so each unit keeps its intended form.
Post-production checks include visual inspection, dimensional verification and a trial fit on the XCMG coolant line fixture.
Sample pipes from each batch undergo pressure, salt spray and vibration tests to confirm long-term performance.
Low-cost aftermarket pipes often use thin-wall tubing that bulges under pressure and rusts quickly in wet conditions.
A pipe with the wrong bend or length stresses the hose connections, which leads to seepage and repeated rework.
The genuine 801970620 is formed to the XCMG drawing, so the 10 mm bore, 1100 mm length, bend path and ends match the original part.
Using genuine XCMG parts also preserves warranty coverage, protects resale value and keeps compatibility with other OEM components.
Backed by XCMG global quality standards and technical support, this water pipe performs reliably on harsh job sites.
Choosing the genuine 801970620 pipe prevents a small coolant weep from turning into an expensive engine repair.
A failed water pipe drains the cooling system fast, which overheats the engine and can warp the cylinder head.
Correct wall thickness and proper coating keep the pipe working across a long service life, reducing replacement frequency.
Reliable coolant delivery also extends radiator, pump and seal life, lowering the total cost of ownership for fleets.
Service records from construction and mining fleets show genuine XCMG cooling parts cut unplanned downtime.
XCMG applies sustainable manufacturing to the 801970620 pipe through efficient bending programs and reduced material waste.
The long service life of the pipe reduces material consumption and lowers the environmental footprint of replacement parts.
Preventing coolant leaks protects soil and groundwater and supports compliance on environmentally sensitive sites.
Steel and coating materials in this component comply with RoHS and REACH rules for safe handling and responsible recycling.
The 801970620 water pipe is held in XCMG regional distribution centres across North America, Europe, Asia and Australia.
Each pipe is capped at both ends and packed in a sturdy carton that protects it from bending, dust and moisture in transit.
For fleet-wide orders, XCMG provides volume pricing and consolidated freight options that simplify planning and reduce cost.
Real-time stock visibility and dedicated supply chain support help fill urgent requests quickly, shortening downtime on projects.
Robust packaging preserves factory condition until installation, preventing deformation and thread damage common in stored pipes.
The XCMG Water Pipe φ10×1100 801970620 is a vital cooling component for XCMG excavators, linking the engine, radiator and pump.
Its coolant-resistant body, precise bend shape and anti-corrosion coating deliver dependable flow in hot, wet and dusty environments.
By preventing leaks and kinks, this water pipe reduces downtime, lowers maintenance costs and protects the engine.
Always purchase genuine XCMG parts from authorised dealers to guarantee authenticity, quality and performance for your fleet.
Choose the 801970620 water pipe for dependable coolant flow and lasting operational peace of mind.
Partner with XCMG, your trusted source for heavy equipment engine and hydraulic components that deliver real value.
OEM 801970620 – XCMG Water Pipe φ10×1100 – the definitive water pipe for engine coolant circulation on your excavator. Engineered for heat and coolant resistance, dimensioned for exact fitment, and backed by global quality standards. Trust the original to protect your investment and maximise uptime.
