OEM 319007792 The XCMG Pipe Clamp 319007792 is a genuine OEM clamp that grips a hydraulic pipe and anchors it to the machine frame on XCMG hydraulic excavators.
Stamped with part number 319007792, this factory clamp gives fitters a correctly sized band that holds the tube steady without crushing it.
The clamp is pressed from spring-grade steel strip, edge rolled for safety, then coated so it resists mud, moisture, salt and site chemicals.
Exact inner radius, band width and bolt hole spacing let the clamp bolt to the original mounting point without bending or shimming.
Holding the pipe at the intended height keeps it away from sharp edges and hot parts, which is where most line failures begin.
Every clamp is gauged and trial fitted before packing, so the part that lands on your bench matches the XCMG drawing without rework.
The 319007792 pipe clamp uses spring-grade steel that keeps its tension when a pressurized pipe pushes outward against the band.
Its diameter and hole spacing follow the OEM pattern, so the clamp bolts to the frame without opening, closing or slotting.
Rolled edges protect the pipe surface from cuts, which removes a common starting point for cracks and pressure loss.
A plated or coated finish fights rust through wet seasons, washdowns and salt spread on winter haul roads.
Correct band width spreads clamping load, so the tube stays round and flow stays smooth instead of being pinched.
Firm retention stops the line from swaying into frame edges or hot manifolds, which is where abrasion damage starts.
Because the part fits straight out of the carton, a technician finishes the job in minutes rather than fabricating a substitute.
Production opens with certified steel strip checked for thickness, temper, width and surface condition before stamping.
Press tools shape the band to the drawing diameter, and edge rolling removes burrs that could cut a pipe wall.
Holes are punched in a jig so spacing stays consistent, which lets bolts start by hand on the machine frame.
Inspectors verify diameter, width, thickness and hole position against a checking gauge made for this part number.
Batch records trace every 319007792 clamp to its steel coil and press tool, so any question is traced and settled fast.
The clamp holds a pipe against the frame so the line stays on its designed route through every work cycle.
A loose or broken clamp lets the pipe swing and rub, which wears the wall thin and can end in a sudden burst.
The genuine 319007792 keeps the pipe at the right height, so clearance to moving parts and hot surfaces is preserved.
Steady retention also reduces stress at the fittings, which lowers the chance of weeping joints and loose connections.
Sound pipe support protects pumps, valves and cylinders, which keeps cycle times and machine availability predictable.
The 319007792 pipe clamp installs with a socket set and torque wrench during scheduled hydraulic or structural service.
Relieve hydraulic pressure, stop the engine and support the pipe before removing any clamp along the route.
Unbolt the old clamp, clean the mounting face and check the frame threads for rust, damage or cross-threading.
Seat the new clamp over the pipe, start the bolt by hand, then torque it so the line is held but not squeezed flat.
Confirm the clamp base sits flush on the frame and that no gap or tilt exists under the band.
Start the engine, cycle the functions slowly, and watch the clamp and nearby line for shifting or rubbing.
At service intervals, recheck bolt torque and look for chipped plating, rust bloom or a stretched clamp.
Every 319007792 clamp is produced in an ISO 9001 and ISO 14001 certified plant with traceability from steel to sealed carton.
Incoming strip is tested for thickness and temper, and finished clamps are gauged for diameter, width and hole position.
During production, press force, tool wear and coating thickness are monitored so each unit matches the reference sample.
Final checks include visual inspection, dimensional verification and a trial fit on the XCMG pipe fixture for this machine series.
Samples from each batch undergo holding load, salt spray and vibration tests to confirm long-term performance.
Cheap copies often use thin strip that bends open under load and loses its grip on the pipe within a few shifts.
A clamp with the wrong diameter pinches the tube or leaves it loose, and both cases end in chafing or leaking.
The genuine 319007792 is formed to the XCMG drawing, so diameter, width and hole spacing mirror the original part.
Staying with genuine XCMG parts keeps warranty cover intact, protects resale value and avoids clashes with other OEM items.
Every clamp carries XCMG global quality standards and technical backing, so it works through long shifts in harsh ground.
Fitting the genuine 319007792 clamp stops a small rub from growing into a costly hydraulic pipe replacement.
When a clamp gives way, the pipe can wear through and dump oil fast, which can take out a pump in minutes.
Proper strip thickness and reliable plating keep the clamp working across a long service life, reducing replacement frequency.
Steady pipe retention also lengthens hose, seal and oil life, which trims the total cost of ownership for fleet owners.
Maintenance logs from quarry and construction fleets show genuine XCMG parts reduce unplanned stoppages.
XCMG builds the 319007792 clamp with efficient nesting and controlled stamping that keep material scrap low.
A long working life means fewer replacements, which lowers the raw material and energy tied to each clamp.
Containing hydraulic leaks protects soil and groundwater, helping operators meet rules on sensitive job sites.
The steel and plating in this part comply with RoHS and REACH requirements for safe handling and responsible recycling.
The 319007792 pipe clamp is stocked in XCMG depots serving North America, Europe, Asia and Australia.
Each clamp is bagged and boxed in strong cartons that guard against bending, dust and damp during transport.
Fleet buyers can request volume pricing and combined freight, which simplifies planning and lowers landed cost.
Live stock data and responsive supply teams help cover urgent requests fast, so machines return to work sooner.
Careful packing keeps the clamp in factory condition until fitting, avoiding the deformation seen in badly stored stock.
The XCMG Pipe Clamp 319007792 is a key retention part on XCMG excavators, holding hydraulic pipes at the correct height and angle.
Its spring-grade steel band, rolled edges and durable coating deliver dependable grip in hot, wet and dusty conditions.
By blocking chafing and fatigue, this pipe clamp cuts downtime, lowers repair bills and adds service life to the line.
Buy only genuine XCMG parts from authorised dealers to secure real quality, correct fitment and lasting performance.
Specify the 319007792 pipe clamp for a dependable hold and confident, trouble-free servicing.
Work with XCMG, a trusted supplier of engine and hydraulic components for heavy equipment that delivers real value.
OEM 319007792 – XCMG Pipe Clamp – the definitive pipe clamp for hydraulic line retention on your excavator. Built for strength, formed for exact fitment, and supported by global quality standards. Trust the original to protect your investment and keep uptime high.
