OEM 800164284 The XCMG Air Hose 800164284 is a genuine OEM air hose that moves compressed air between the compressor, dryer and pneumatic control valves on XCMG hydraulic excavators.
Marked with part number 800164284, this factory hose gives technicians a flexible, sealed line that keeps air pressure steady through heat, dust and long shifts.
The tube is molded from air-resistant synthetic rubber, reinforced with a woven textile braid, and finished with a tough outer cover against abrasion.
Exact bore, working length and end fittings let the hose push onto the original nipples without trimming, extra clamps or improvised adapters.
A tight, flexible path prevents air loss, so brake release and air-assisted attachments respond the instant the operator moves a lever.
Every hose is pressure tested and measured before packing, so the part that arrives at your workshop matches the XCMG drawing without adjustment.
The 800164284 air hose is molded from air-tight rubber that stays flexible in cold starts and holds firm beside hot engine parts.
Its textile braid checks expansion, so the hose does not balloon when the compressor cycles and pressure spikes through the line.
The pre-formed route mirrors the factory layout, so the hose clears covers, brackets and pulleys without brushing or rubbing.
A dense outer cover resists grit, oil mist and constant flexing, which are the usual reasons a working hose develops pinholes.
Correct bore and cut length let the original clamps and fittings seat properly, so the joint seals without extra tape or sealant.
Flexible rubber absorbs engine movement, which spares the compressor outlet threads and air valve nipples from stress.
An air-tight line keeps brake release crisp and air controls quick, which makes the machine safer and more productive.
Each run starts with certified compound tested for hardness, tensile strength, air permeability and heat ageing before building.
The tube and braid are laid on a mandrel shaped to the OEM path, so the finished hose keeps its curve and full bore.
Vulcanizing bonds tube, braid and cover into one wall, and end trimming leaves a clean edge with no loose fibers.
Inspectors measure bore, length, wall thickness and surface quality on samples cut from every curing batch.
Records tie each 800164284 hose to its compound lot and press number, so any question is traced and closed quickly.
This hose carries compressed air from the compressor and dryer to the air valves, giving controlled pressure wherever the circuit needs it.
A split or loose hose bleeds pressure, which slows brake release, weakens air functions and makes the compressor work harder.
The genuine 800164284 holds pressure tight, so functions answer promptly and the compressor runs fewer cycles.
Keeping the hose clear of hot manifolds and sharp edges stops the rubber from baking or cutting, which lengthens life.
Steady air supply protects valves, cylinders and brake chambers, which keeps cycle times and machine availability stable.
The 800164284 air hose fits with hose clamp pliers and ordinary hand tools during a normal service visit.
Drain the air system, stop the engine and release leftover pressure before loosening any connection.
Take off the old hose, wipe both nipples clean and look for rust, cracks or squashed beads that could leak.
Push the new hose onto each nipple without twisting, then set the clamps straight behind the bead at both ends.
Build pressure, listen for hissing and brush soapy water on each joint to confirm the seal is sound.
At each service interval, feel the hose for soft spots, glazing or small cracks near the bend and fittings.
Swap the hose at the first sign of hardening, since a burst air line can take out brakes or controls on site.
The 800164284 hose is built in a plant holding ISO 9001 and ISO 14001 certificates, with records from compound to carton.
Incoming rubber is checked for hardness and air permeability, and finished hoses are gauged for bore, length and wall.
Operators log cure time, steam temperature and mandrel condition so every hose cures the same way as the last.
Final checks cover appearance, dimensions and a trial fit on the XCMG air line fixture used for this machine series.
Samples from each batch go through pressure, burst and heat ageing tests to prove long-term performance in the field.
Bargain copies often use recycled rubber that stiffens in a season and splits along the bend beside the engine.
A hose with the wrong bore or length can kink after fitting, which chokes air flow and causes slow, spongy response.
The genuine 800164284 is built to the XCMG drawing, so bore, length, route and compound match the original part.
Staying with genuine XCMG parts keeps warranty cover intact, protects resale value and avoids clashes with other OEM items.
Every hose carries XCMG global quality standards and technical backing, so it works through long shifts in harsh ground.
Fitting the genuine 800164284 hose stops a small air leak from growing into a major system repair.
A burst air line can disable brakes or controls, which halts production and puts the crew at risk.
Sound rubber and correct reinforcement keep the hose working over a long life, which cuts how often it must be replaced.
Reliable air supply also extends compressor, valve and seal life, which trims the total cost of ownership for fleets.
Maintenance logs from quarry and construction fleets show genuine XCMG parts reduce unplanned stoppages.
XCMG builds the 800164284 hose with efficient mandrel cycles and tight material control that keep production scrap low.
A long working life means fewer replacements, which lowers the raw material and energy tied to each hose.
Stopping air leaks keeps the compressor from running longer than needed, which saves fuel and cuts emissions.
The rubber in this part complies with RoHS and REACH requirements for safe handling and responsible disposal.
The 800164284 air hose is stocked in XCMG depots serving North America, Europe, Asia and Australia.
Each hose is sleeved and boxed in strong cartons that guard against kinking, dust and sunlight during transport.
Fleet buyers can request volume pricing and combined freight, which simplifies planning and lowers landed cost.
Live stock data and responsive supply teams help cover urgent requests fast, so machines return to work sooner.
Careful packing keeps the hose in factory condition until fitting, avoiding the flattening seen in badly stored stock.
The XCMG Air Hose 800164284 is a key supply part on XCMG excavators, linking the compressor and dryer to the air control circuit.
Its air-resistant tube, textile braid and tough cover deliver dependable pressure in hot, wet and dusty conditions.
By preventing air loss and chafing, this hose cuts downtime, lowers repair bills and keeps controls responsive.
Buy only genuine XCMG parts from authorised dealers to secure real quality, correct fitment and lasting performance.
Specify the 800164284 air hose for a dependable connection and confident, trouble-free servicing.
Work with XCMG, a trusted supplier of engine and hydraulic components for heavy equipment that delivers real value.
OEM 800164284 – XCMG Air Hose – the definitive air hose for compressed-air supply on your excavator. Built for pressure and heat resistance, shaped for exact fitment, and supported by global quality standards. Trust the original to protect your investment and keep uptime high.
