OEM 329900510 The XCMG U-Bend Clamp 329900510 is a genuine OEM clamp that supports a hydraulic pipe exactly where it turns, keeping the line steady on XCMG excavators.
Carrying part number 329900510, this factory clamp gives mechanics a shaped steel saddle that matches the tube radius and holds it against the frame.
The clamp is stamped from quality steel strip, drilled in a fixture, then coated so it survives mud, water, salt and site chemicals.
Correct radius, width and hole spacing let the clamp bolt straight on, with no bending, filing or improvised rubber packing.
Supporting the bend spreads vibration energy along the tube, which reduces fretting marks and stress on the nearby fitting threads.
Each clamp is gauged and trial fitted before packing, so what arrives at your workshop matches the XCMG drawing without adjustment.
The 329900510 clamp is pressed from steel strip thick enough to resist flattening when a loaded line pushes hard against the saddle.
Its radius is set by a forming die, so the curve matches the tube without pinching it or leaving a gap underneath.
Drilled holes sit at the OEM spacing, which means bolts start by hand and tighten straight without slotting or reaming.
The anti-corrosion coating survives mud, washdown water and road salt, so the clamp keeps its strength through many seasons.
Rounded contact edges protect the tube surface, which avoids the deep scratch marks that later become crack starters.
A generous width spreads the clamping load, which keeps the tube round so flow and pressure remain steady.
Because the part fits straight out of the box, technicians spend minutes instead of hours on a routine line repair.
Every batch starts with certified steel strip checked for thickness, hardness, flatness and surface condition before stamping.
Press dies are maintained on a set schedule, so the radius and width repeat from the first stroke to the last of the run.
Holes are drilled or punched in a jig, which keeps spacing consistent and guarantees the clamp drops onto the frame studs.
Quality staff compare radius, width, thickness and hole spacing against a checking gauge made for this part number.
Records tie each 329900510 clamp to its steel coil and press die, so any concern is traced and resolved without delay.
This clamp wraps around a pipe at the bend and pins it to a frame or bracket, so the line cannot sway with machine motion.
An unsupported bend flexes every cycle, and that repeated movement slowly cracks the tube wall beside the fitting.
The genuine 329900510 holds the pipe at the intended radius, so bending load is distributed instead of concentrated at one point.
Holding the line at the right height also keeps it clear of frame edges and hot surfaces, which prevents rubbing and heat damage.
Firm, even support protects pumps, valves and cylinders, which keeps cycle times and machine availability predictable.
Fitting the 329900510 clamp takes a socket set and a torque wrench during normal hydraulic or structural service work.
Release hydraulic pressure, stop the engine and support the pipe before loosening any clamp along the route.
Unbolt the old clamp, clean the frame surface and check the studs or threads for rust, damage or cross-threading.
Guide the new clamp over the tube, thread the bolts by hand, then torque them so the pipe is held firmly but not squeezed.
Confirm the tube sits fully in the saddle and the clamp base touches the frame with no gap or tilt.
Run the engine, move each function slowly, and watch the clamp and line for shifting, rubbing or leaking.
At service intervals, recheck bolt torque and inspect for chipped paint, rust bloom or a bent clamp body.
Every 329900510 clamp is made in a plant certified to ISO 9001 and ISO 14001, with records from steel coil to sealed carton.
Incoming strip is tested for thickness and grade, and finished clamps are gauged for radius, width and bolt hole spacing.
Operators monitor press force, die wear and coating thickness so each unit keeps the same shape as the reference sample.
Final checks cover appearance, dimensions and a trial fit on the XCMG hydraulic pipe fixture used for this machine family.
Samples from every batch go through load, salt spray and vibration tests to prove long-term performance in the field.
Cheap copies often use thin strip that flattens the first time a pressure line kicks, and the coating fails within months.
A clamp with a smaller radius pinches the tube, which raises pressure loss and can start a crack at the bend.
The genuine 329900510 is stamped to the XCMG drawing, so radius, width, thickness and hole spacing mirror the original.
Sticking with genuine XCMG parts keeps warranty cover intact, protects resale value and avoids clashes with other OEM items.
Every clamp carries XCMG global quality standards and technical backing, so it works through long shifts on hard ground.
Fitting the genuine 329900510 clamp stops a minor rub from growing into a major hydraulic line repair.
When a clamp gives way, the line can fatigue through and dump oil fast, damaging the pump before anyone notices.
Sound steel thickness and reliable coating keep the clamp working over a long life, which cuts how often it must be replaced.
Steady line support also lengthens hose, seal and oil life, which trims the total cost of ownership for fleet owners.
Maintenance logs from quarry and construction fleets show genuine XCMG hydraulic parts reduce unplanned stoppages.
XCMG builds the 329900510 clamp with efficient nesting and controlled stamping that keep material scrap low.
A long working life means fewer replacements, which lowers the raw material and energy tied to each clamp.
Containing hydraulic leaks protects soil and groundwater, helping operators meet rules on sensitive job sites.
The steel and coating in this part comply with RoHS and REACH requirements for safe handling and responsible recycling.
The 329900510 U-bend clamp is stocked in XCMG depots serving North America, Europe, Asia and Australia.
Each clamp is wrapped and boxed in strong cartons that guard against bending, dust and damp during transport.
Fleet buyers can request volume pricing and combined freight, which simplifies planning and lowers landed cost.
Live stock data and responsive supply teams help cover urgent requests fast, so machines return to work sooner.
Careful packing keeps the clamp in factory condition until fitting, avoiding the deformation seen in badly stored stock.
The XCMG U-Bend Clamp 329900510 is a key support part on XCMG excavators, holding hydraulic lines at the correct bend radius.
Its pressed steel body, accurate curve and anti-corrosion coating deliver dependable support in hot, wet and dusty conditions.
By blocking chafing and fatigue, this U-bend clamp cuts downtime, lowers repair bills and adds service life to the line.
Buy only genuine XCMG parts from authorised dealers to secure real quality, correct fitment and lasting performance.
Specify the 329900510 U-bend clamp for a dependable hold and confident, trouble-free servicing.
Work with XCMG, a trusted supplier of engine and hydraulic components for heavy equipment that delivers real value.
OEM 329900510 – XCMG U-Bend Clamp – the definitive U-bend clamp for hydraulic line bends on your excavator. Built for strength, shaped for exact fitment, and supported by global quality standards. Trust the original to protect your investment and keep uptime high.
