The 800107067 Hose is a genuine XCMG hydraulic line designed for motor grader transmission cooler circuits, hydraulic tank return lines, and low‑pressure suction applications. This flexible hose assembly safely transports warm oil from the torque converter or hydraulic system to the cooler and back to the sump on XCMG GR135, GR165, GR180, GR215, GR260, GR300, and GR350 motor graders.
Constructed from oil‑resistant synthetic rubber with textile reinforcement and a helical steel wire (to resist collapse under vacuum), the 800107067 hose withstands temperatures up to +120°C and working pressures up to 1.5 MPa (217 psi). Factory‑crimped or clamped end fittings ensure leak‑free connections to transmission oil coolers, filters, and pump inlets.
A cracked, hardened, or softened hose can cause oil starvation, overheating, or catastrophic fluid loss. Replacing a degraded hose with genuine XCMG 800107067 restores oil flow, protects the transmission from thermal damage, and prevents environmental spills. The hose meets SAE 100R4 and ISO 3862 standards for suction and return lines.
Using genuine XCMG guarantees correct hose length, inner diameter, and end fitting orientation for a perfect drop‑in fit. Always replace suspect hoses with the OEM 800107067 assembly.
| Parameter | Specification |
|---|---|
| OEM Number | 800107067 |
| Brand | XCMG (Genuine Original Equipment) |
| Product Type | Hydraulic Suction / Return Hose (SAE 100R4) |
| Hose Inner Diameter | 25 mm (1 inch) |
| Overall Length (End to End) | 520 mm ± 5 mm |
| Reinforcement | Two textile braids + steel helix wire (vacuum resistant) |
| End Fittings Type | Swivel 45° flanged (SAE J518) or straight barbed with hose clamps |
| Maximum Working Pressure | 1.5 MPa (217 psi) – return line |
| Maximum Vacuum Rating | -0.08 MPa (-11.6 psi) – full vacuum without collapse |
| Burst Pressure | 6.0 MPa (870 psi) – 4:1 safety factor |
| Operating Temperature Range | -40°C to +120°C (-40°F to +248°F) |
| Inner Tube Material | Nitrile rubber (oil resistant, high flexibility) |
| Cover Material | Black synthetic rubber (ozone & abrasion resistant) |
| Minimum Bend Radius | 125 mm (static), 150 mm (dynamic) |
| Standards Compliance | SAE J517 Type R4, ISO 3862-1, DIN EN 853 |
| Corrosion Protection (Fittings) | Zinc‑nickel plating, 720h salt spray |
| Compatible Models | XCMG GR135, GR165, GR180, GR215, GR260, GR300, GR350 motor graders |
| Superseded Part Numbers | 800107045, 800107088, 800107102 |
The XCMG 800107067 Hose plays a vital role in keeping the grader’s transmission and hydraulic oil within safe operating temperatures.
It carries hot oil from the torque converter or main pump outlet to the radiator‑type oil cooler, then returns cooled oil to the transmission sump or hydraulic tank.
A blocked or collapsed hose restricts oil flow, causing rapid overheating, loss of hydraulic power, and severe damage to clutches and bearings.
The 800107067’s steel helix reinforcement prevents the hose from collapsing under suction, ensuring steady oil supply even during cold starts when oil is thick.
On GR215 and GR260 graders, this hose also serves as the main return line from the hydraulic filter to the tank, preventing contamination bypass.
Replacing an aged or softened hose with genuine XCMG 800107067 restores full oil flow, protects the cooling system, and reduces thermal stress.
Each 800107067 hose is manufactured using high‑precision extrusion and reinforcement braiding processes in XCMG’s ISO 9001 certified facility.
The inner tube is extruded from special NBR compound that resists oil degradation and remains flexible at -40°C.
Over the tube, two layers of high‑tensile textile braid are applied, followed by a galvanized steel helix wire to provide vacuum resistance.
Finally, a synthetic rubber cover is extruded and vulcanized for abrasion and ozone protection. All end fittings are crimped using CNC controlled machines.
Each assembly undergoes 100% vacuum test (-0.09 MPa for 30 seconds) as well as a pressure proof test at 2.5 MPa.
XCMG’s quality control also includes a 72‑hour heat aging test at +120°C and cold flexibility at -40°C. Counterfeit hoses rarely survive these tests.
Genuine hoses are laser‑etched with the part number 800107067 for full traceability and backed by a 12‑month warranty.
Replacing the 800107067 suction or return hose begins by draining the transmission or hydraulic oil below the connection level, or isolating with valves.
Clean the area around both fittings to avoid dirt ingress. Using a backup wrench, loosen the hose ends and remove the old assembly.
Inspect the tank nipple and pump port for damage or old seal remnants. Always replace sealing O‑rings or gaskets.
Position the new 800107067 hose so that it follows the original routing without sharp bends. Minimum bend radius is 125 mm – excessive bending restricts flow.
Hand‑tighten the fittings, then torque to specification: for flanged connections, use 50 Nm on bolts; for barbed fittings, tighten clamp to 5 Nm.
Fill the hydraulic tank or transmission, start the engine, and check for leaks and proper oil flow. Listen for pump cavitation (should be quiet).
XCMG recommends inspecting the hose every 1,000 hours and replacing it at 4,000 hour intervals or sooner if cracks, bulging, or hardening are seen.
Aftermarket “universal” suction hoses often lack the embedded steel helix wire, leading to collapse under vacuum at higher engine speeds.
This collapse starves the pump of oil, causing cavitation damage and eventual pump seizure. The genuine 800107067 incorporates a full‑coverage helix.
Aftermarket hoses also use lower‑grade rubber that swells when exposed to hot hydraulic oil, reducing flow and possibly blocking the cooler.
Many generic hoses have incorrect fitting orientations or crimp dimensions, making installation difficult and prone to leaks.
The 800107067 is factory‑pre‑angled to match the exact port geometry on XCMG GR graders, saving installation time and eliminating stress.
Additionally, counterfeit products often fail pressure and impulse tests, while genuine XCMG hoses are individually proof‑tested. Protect your grader’s heart – the hydraulic pump – with genuine 800107067.
XCMG provides a full 12‑month warranty, and using genuine parts preserves your machine’s resale value and ensures full compatibility with other OEM components.
Watch for these symptoms indicating the 800107067 hose needs replacement: visible cracks or bulges on the outer cover, a soft or flattened feel when squeezed, pump whining noise (cavitation), and slow hydraulic implement response.
Also, if the transmission temperature gauge reads consistently high, a blocked or collapsed return hose may be restricting oil flow to the cooler.
During daily walk‑around inspections, visually examine the hose for chafing against frame members or other hoses. Listen for unusual pump noise.
If you see small cracks in the cover near the fittings, internal reinforcement may be corroded. Replace the hose at the first sign of deterioration.
Preventive replacement every 4,000 hours or three years (whichever comes first) is recommended for all hydraulic suction and return hoses.
The cost of a genuine 800107067 is minimal compared to replacing a hydraulic pump or transmission damaged by overheating.
Keep a log of hose replacements and always use OEM parts for critical cooling circuits.
The 800107067 Hose is stocked in XCMG regional distribution hubs: North America (Houston, TX), Europe (Rotterdam), Middle East (Dubai), and Asia (Shanghai).
Standard air freight deliveries take 2‑5 business days to most international destinations. Express courier services (DHL/UPS/FedEx) are available for 1‑2 day emergency shipments.
Bulk orders (15+ units) can be shipped via sea freight with significant cost savings. Each hose assembly is individually sealed in anti‑static plastic and packed in reinforced cardboard boxes.
For large mining or construction fleets, XCMG offers consignment stocking programs – parts are stored on‑site and invoiced as they are used, eliminating order lead times.
Don’t let a collapsed suction hose disable your grader in the middle of a critical project. The genuine XCMG 800107067 provides reliable oil flow, vacuum resistance, and long service life.
Order now and experience the peace of mind that comes with using original equipment. With precise factory fitment and superior materials, the 800107067 is the only choice for your XCMG motor grader.
Upgrade your motor grader’s hydraulic reliability with the XCMG 800107067 Hose – engineered for high‑flow cooling circuits, return lines, and long‑term durability.
Order today and keep your grader’s transmission and hydraulic oil at optimal temperatures, maximizing machine life and uptime.
Choose genuine XCMG – order the 800107067 now.
